Read Time4 Minutes, 33 Seconds

Below are the best explained ways on how to clean keurig with vinegar. Keurigs mean you no longer have to think about wrangling filters and ground coffee beans every morning. But many of us are probably guilty of not thinking about cleaning it either — and that thing can get dirty. KDKA-TV of Pittsburgh swabbed 28 machines and found more than half contained harmful bacteria. Grossed out? Us too. let see how to maintain your go-to morning machine. Start by buying the following cleaning essentials, then follow this timeline for how often you should clean every part of your brewer.

What you’ll need:

PLAN - PRICE

Description

Filter - $24.99 

Keurig Water Filter Refill Cartridges

Viniger - $2.49 

Heinz White Vinegar

Descale Sol - 

$8.03

Keurig Descaling Solution

How to clean keurig with vinegar each parts

How to clean keurig with vinegar on outerside?

With a wet, soapy, lint-free cloth, wipe away dust or splatters. Then, gently slide out the drip tray, empty, wipe, and return to its position. But never, ever submerge the machine in water. It is an electrical appliance, after all.

Removing stains on keurig with vinegar on it’s individual parts?

Turn off and unplug the machine and allow it to cool.

Next, lift up the lever to disassemble the K-Cup pod holder and funnel, and wash both parts in the sink or on the top shelf of the dishwasher on a low temperature cycle.

While you’re at it, loosen any potential clogs from the “entrance needle” (that thing that pierces the pods) as well as the “exit needle” underneath the pod holder using a clean paperclip like so. (But be careful—those things are sharp!)

Remove the water reservoir and lid and wash both with soapy water in the sink—not the dishwasher. Rinse thoroughly and spray the filter with a faucet hose, or shake the reservoir to create a more forceful stream of water. But when you’re done, don’t towel-dry the inside, as you could leave some lint behind.

  • Clean up keurig with vinegar every week: Unplug the machine and clean the mug tray and K-cup holder in warm soapy water. For the water reservoir and lid, remove the water filter, then wipe the surfaces with a damp, soapy cloth. Rinse with water and let air dry — you don’t want to dry it with a cloth since this could leave lint behind. Finish by wiping down the exterior surface with a wet sponge before plugging it back in.
  • Clean keurig with vinegar every two months: Replace your water filter cartridge to keep your coffee fresh every other month. Start by soaking a new cartridge in fresh water for five minutes, then rinse it for 60 seconds. Wash the mesh of the lower filter holder, insert the cartridge into the upper filter holder, and snap on the lid. Finally, put it back into your reservoir and lock it into place.
  • Clean keurig with vinegar every three to six months: Descale your machine to remove hard water minerals that can build up over time, which could affect how well it works. Begin by filling the reservoir with 10 ounces of white vinegar — or you can use Keurig’s Descaling Solution. Start the brew cycle without a K-cup and let the machine run as usual, using a mug to catch the liquid. Repeat this process a second time. Then, repeat the process one last time, but with 10 ounces of fresh water.
  • How to clean keurig with vinegar as needed: When you see grounds in your K-cup holder, remove them with a sponge to prevent them from ending up in your beverage tomorrow morning. If you’re having trouble brewing, there may also be coffee grounds stuck in the needles, which punch the entrance and exit points the water flows through.

To clean them, first unplug the machine. Keurig recommends then carefully using a paperclip to clear away any debris lodged in the needles clogging before rinsing. (See where to find them in this video.) For a Keurig 2.0, you can use the Keurig brewer maintenance accessory instead.

As long as you follow these steps, you won’t have to worry about anything other than coffee being in your morning brew (well, unless you like yours with milk and sugar, that is).

How do you descale a Keurig using vinegar?

Empty the water reservoir and, if applicable, the filter. Turn off the machine. Fill the reservoir with 10 ounces of white vinegar.

Next, place a big, ceramic mug (not paper!) under the spout and (without adding a K-Cup), hit that beloved brew button.

Empty the contents of the mug, then refill the reservoir with 10 ounces of only water and repeat, letting the Keurig sit for 30 minutes when complete.

After that, remove and rinse the reservoir, fill it to the full line with fresh water, and repeat brew cycles until all the water is gone.

How do you descale a Keurig using descaling solution?

Perform the functions described above, but instead of using vinegar, fill the reservoir with a bottle of Keurig’s descaling solution. Before moving on to the next step, fill the now-empty descaling solution bottle with water and pour that into the reservoir as well.

Hit the “brew” button to perform a cleansing brew into a ceramic mug (remember, don’t use paper here!). Repeat until “Add Water” is illuminated. At that point, let the Keurig rest for 30 minutes.

After that, remove and rinse the reservoir, fill it to the full line with fresh water, and repeat brew cycles until all of the water is gone (or 12 times, as recommended by the Keurig Descaling Solution manufacturer).

0 0
Happy
Happy
0 %
Sad
Sad
0 %
Excited
Excited
0 %
Sleppy
Sleppy
0 %
Angry
Angry
0 %
Surprise
Surprise
0 %


Leave a Reply

Your email address will not be published. Required fields are marked *